회원 및 비회원 모두 열람이 가능합니다. 최대 업로드 가능한 용량은 20MB 입니다.
글 수 1,910
근래 포팅하고 있는 6400 board를 거의 살렸습니다.
MDS technology의 M6 board입니다.
smdk6400이랑 회로가 많이 틀려서 좀 삽질을 심하게 했습니다만
꽤 깔끔하게 동작을 시켰습니다.
동영상쪽과 무선랜 드라이버 SD정도만 잡으면 끝이 보일 듯 합니다.
^^
=====================================================
U-Boot 1.1.6 (Aug 20 2008 - 01:01:27) for SMDK6400
CPU: S3C6400@400MHz
Fclk = 400MHz, Hclk = 100MHz, Pclk = 50MHz , Serial = CLKUART (ASYNC Mode)
Board: SMDK6400
DRAM: 128 MB
Flash: 0 kB
NAND: 128 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
dm9000 i/o: 0x30000300, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:40:5c:26:0a:5b
operating at 100M full duplex mode
TFTP from server 192.168.0.249; our IP address is 192.168.0.102
Filename 'zImage'.
Load address: 0xc0008000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##################################
done
Bytes transferred = 1835268 (1c0104 hex)
Boot with zImage
Starting kernel ...
Uncompressing Linux.................................................................................................................... done, booting the kernel.
Linux version 2.6.21.5-cfs-v19 (root@mds6400) (gcc version 4.2.4) #59 Wed Aug 20 01:24:09 KST 2008
CPU: ARMv6-compatible processor [410fb761] revision 1 (ARMv6TEJ), cr=00c5387f
Machine: MDS6400
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
CPU S3C6400 (id 0xaaaabbbb)
S3C6400: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C6400: EPLL 192.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 32512
Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.249:/opt/4.2.4-eabi-armv6/arm-1176jzfs-linux-gnueabi/sys-root ip=192.168.0.102:192.168.0.249:192.168.0.1:255.255.255.0::eth0:off console=ttySAC0,115200
Trying to install chained interrupt handler for IRQ0
Trying to install chained interrupt handler for IRQ1
Trying to install chained interrupt handler for IRQ32
Trying to install chained interrupt handler for IRQ33
PID hash table entries: 512 (order: 9, 2048 bytes)
timer tcon=00600008, tcnt c34f, tcfg 00000400,00000000, usec 0000199a
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126080KB available (3272K code, 287K data, 200K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
s3c6400: Initialising architecture
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
yaffs Aug 20 2008 01:19:36 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
LCD TYPE :: S3C_MDS430 LCD will be initialized
S3C_LCD clock got enabled :: 100.000 Mhz
Window[0]- FB1 : map_video_memory: clear ff600000:0003fc00
FB1 : map_video_memory: dma=50600000 cpu=ff600000 size=0003fc00
Console: switching to colour frame buffer device 60x34
fb-1069907012: frame buffer device
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
s3c-uart.0: s3c_serial0 at MMIO 0x7f005000 (irq = 37) is a S3C
s3c-uart.1: s3c_serial1 at MMIO 0x7f005400 (irq = 38) is a S3C
s3c-uart.2: s3c_serial2 at MMIO 0x7f005800 (irq = 39) is a S3C
s3c-uart.3: s3c_serial3 at MMIO 0x7f005c00 (irq = 40) is a S3C
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
dm9000 Ethernet Driver
eth0: dm9000 at c8808300,c880a302 IRQ 67 MAC: 08:00:3e:26:0a:5b
S3C NAND Driver, (c) 2007 Samsung Electronics
S3C NAND Driver is using software ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x00040000 : "Bootloader"
0x00040000-0x00200000 : "Kernel"
0x00200000-0x08000000 : "File System"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 47, io mem 0x74300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
S3C Touchscreen driver, (c) 2007 Samsung Electronics
s3c TouchScreen got loaded successfully : 10 bits
input: s3c TouchScreen as /class/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
res->start : 7e005000 res->end : 7e0050ff<6>s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2410-i2c s3c2410-i2c: slave address 0x10
s3c2410-i2c s3c2410-i2c: bus frequency set to 195 KHz
s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
[s3c_hsmmc_probe]: s3c-hsmmc.0: at 0xc8812000 with irq 56. clk src: hsmmc0 sclk_48m_mmc0
[s3c_hsmmc_probe]: s3c-hsmmc.1: at 0xc8814000 with irq 57. clk src: hsmmc1 sclk_48m_mmc1
[s3c_hsmmc_probe]: s3c-hsmmc.2: at 0xc8816000 with irq 49. clk src: hsmmc2 sclk_48m_mmc2
Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC).
ASoC version 0.13.2
WM9713/WM9714 SoC Audio Codec 0.12
asoc: AC97 HiFi <-> s3c6400-ac97 mapping ok
ALSA device list:
#0: SMDK6400 (WM9713)
TCP cubic registered
NET: Registered protocol family 1
s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time
eth0: link down
IP-Config: Complete:
device=eth0, addr=192.168.0.102, mask=255.255.255.0, gw=192.168.0.1,
host=192.168.0.102, domain=, nis-domain=(none),
bootserver=192.168.0.249, rootserver=192.168.0.249, rootpath=
Looking up port of RPC 100003/2 on 192.168.0.249
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Looking up port of RPC 100005/1 on 192.168.0.249
VFS: Mounted root (nfs filesystem).
Freeing init memory: 200K
INIT: version 2.84 booting
rc.udev start
Initializing udev dynamic device directory.
Starting udevd: /sbin/udevd --daemon
rc.udev start after
mount: Mounting /dev/root on / failed: No such file or directory
INIT: Entering runlevel: 3
[: 0: unknown operand
Linux 2.6.21-MEP2440
/) /)
(='.'=)
login[2279]: root login on `tts/0'
root@godori:~# aplay g.wav
Playing WAVE 'g.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
MDS technology의 M6 board입니다.
smdk6400이랑 회로가 많이 틀려서 좀 삽질을 심하게 했습니다만
꽤 깔끔하게 동작을 시켰습니다.
동영상쪽과 무선랜 드라이버 SD정도만 잡으면 끝이 보일 듯 합니다.
^^
=====================================================
U-Boot 1.1.6 (Aug 20 2008 - 01:01:27) for SMDK6400
CPU: S3C6400@400MHz
Fclk = 400MHz, Hclk = 100MHz, Pclk = 50MHz , Serial = CLKUART (ASYNC Mode)
Board: SMDK6400
DRAM: 128 MB
Flash: 0 kB
NAND: 128 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
dm9000 i/o: 0x30000300, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 00:40:5c:26:0a:5b
operating at 100M full duplex mode
TFTP from server 192.168.0.249; our IP address is 192.168.0.102
Filename 'zImage'.
Load address: 0xc0008000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##################################
done
Bytes transferred = 1835268 (1c0104 hex)
Boot with zImage
Starting kernel ...
Uncompressing Linux.................................................................................................................... done, booting the kernel.
Linux version 2.6.21.5-cfs-v19 (root@mds6400) (gcc version 4.2.4) #59 Wed Aug 20 01:24:09 KST 2008
CPU: ARMv6-compatible processor [410fb761] revision 1 (ARMv6TEJ), cr=00c5387f
Machine: MDS6400
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
CPU S3C6400 (id 0xaaaabbbb)
S3C6400: core 400.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C6400: EPLL 192.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 32512
Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.249:/opt/4.2.4-eabi-armv6/arm-1176jzfs-linux-gnueabi/sys-root ip=192.168.0.102:192.168.0.249:192.168.0.1:255.255.255.0::eth0:off console=ttySAC0,115200
Trying to install chained interrupt handler for IRQ0
Trying to install chained interrupt handler for IRQ1
Trying to install chained interrupt handler for IRQ32
Trying to install chained interrupt handler for IRQ33
PID hash table entries: 512 (order: 9, 2048 bytes)
timer tcon=00600008, tcnt c34f, tcfg 00000400,00000000, usec 0000199a
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126080KB available (3272K code, 287K data, 200K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
s3c6400: Initialising architecture
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
yaffs Aug 20 2008 01:19:36 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
LCD TYPE :: S3C_MDS430 LCD will be initialized
S3C_LCD clock got enabled :: 100.000 Mhz
Window[0]- FB1 : map_video_memory: clear ff600000:0003fc00
FB1 : map_video_memory: dma=50600000 cpu=ff600000 size=0003fc00
Console: switching to colour frame buffer device 60x34
fb-1069907012: frame buffer device
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
s3c-uart.0: s3c_serial0 at MMIO 0x7f005000 (irq = 37) is a S3C
s3c-uart.1: s3c_serial1 at MMIO 0x7f005400 (irq = 38) is a S3C
s3c-uart.2: s3c_serial2 at MMIO 0x7f005800 (irq = 39) is a S3C
s3c-uart.3: s3c_serial3 at MMIO 0x7f005c00 (irq = 40) is a S3C
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
dm9000 Ethernet Driver
eth0: dm9000 at c8808300,c880a302 IRQ 67 MAC: 08:00:3e:26:0a:5b
S3C NAND Driver, (c) 2007 Samsung Electronics
S3C NAND Driver is using software ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x00040000 : "Bootloader"
0x00040000-0x00200000 : "Kernel"
0x00200000-0x08000000 : "File System"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 47, io mem 0x74300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
S3C Touchscreen driver, (c) 2007 Samsung Electronics
s3c TouchScreen got loaded successfully : 10 bits
input: s3c TouchScreen as /class/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
res->start : 7e005000 res->end : 7e0050ff<6>s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2410-i2c s3c2410-i2c: slave address 0x10
s3c2410-i2c s3c2410-i2c: bus frequency set to 195 KHz
s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
[s3c_hsmmc_probe]: s3c-hsmmc.0: at 0xc8812000 with irq 56. clk src: hsmmc0 sclk_48m_mmc0
[s3c_hsmmc_probe]: s3c-hsmmc.1: at 0xc8814000 with irq 57. clk src: hsmmc1 sclk_48m_mmc1
[s3c_hsmmc_probe]: s3c-hsmmc.2: at 0xc8816000 with irq 49. clk src: hsmmc2 sclk_48m_mmc2
Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC).
ASoC version 0.13.2
WM9713/WM9714 SoC Audio Codec 0.12
asoc: AC97 HiFi <-> s3c6400-ac97 mapping ok
ALSA device list:
#0: SMDK6400 (WM9713)
TCP cubic registered
NET: Registered protocol family 1
s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time
eth0: link down
IP-Config: Complete:
device=eth0, addr=192.168.0.102, mask=255.255.255.0, gw=192.168.0.1,
host=192.168.0.102, domain=, nis-domain=(none),
bootserver=192.168.0.249, rootserver=192.168.0.249, rootpath=
Looking up port of RPC 100003/2 on 192.168.0.249
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Looking up port of RPC 100005/1 on 192.168.0.249
VFS: Mounted root (nfs filesystem).
Freeing init memory: 200K
INIT: version 2.84 booting
rc.udev start
Initializing udev dynamic device directory.
Starting udevd: /sbin/udevd --daemon
rc.udev start after
mount: Mounting /dev/root on / failed: No such file or directory
INIT: Entering runlevel: 3
[: 0: unknown operand
Linux 2.6.21-MEP2440
/) /)
(='.'=)
login[2279]: root login on `tts/0'
root@godori:~# aplay g.wav
Playing WAVE 'g.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
arm-gcc-eabi 4.2.4
glibc 2.7
등을 새로 구성해서 사용을 했고요.
현재까지는 아무런 이상없이 잘 동작하네요....^^