기존 이솝 임베디드 포럼의 지식인 서비스가 게시판 형태로 변경되었습니다.
IT 인재교육 때 MDS6410보드로 실습하고 회사에서 SDMK6410보드에 포팅 해보려고 하는데요
공유기로 PC랑 보드랑 연결 했구요
유부트 올리고 tftp로 커널 이미지까지 다운로드해서 부팅 되다가
멈춰 버리네요...어떡게 해야 될지 도통 감이 안와서
염치 불구하고 질문 올립니다.
부탁드립니다.
멈출때가지 로그를 아래에 삽입했습니다.
U-Boot 1.3.4 (Sep 29 2009 - 10:48:02) for SMDK6410
CPU: S3C6410@532MHz
Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode)
Board: SMDK6410
DRAM: 128 MB
Flash: 0 kB
SD/MMC: 0 MB
NAND: nand info
SLC 64 OOB NAND
256 MB
In: serial
Out: serial
Err: serial
Net: smc911x
Hit any key to stop autoboot: 0
smc911x: initializing
smc911x: detected LAN9115 controller
smc911x: phy initialized
smc911x: MAC 00:40:5c:26:0a:5b
Using smc911x device
TFTP from server 192.168.100.3; our IP address is 192.168.100.4
Filename 'zImage-2629'.
Load address: 0xc0008000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###################################################
done
Bytes transferred = 2253112 (0x226138)
Boot with zImage
Using machid 0xbb8 from environment
Starting kernel ...
Uncompressing Linux........................................................................................................................................................ done, booting the kernel.
Linux version 2.6.29 (root@mdsedu) (gcc version 4.3.2 (crosstool-NG-1.3.2) ) #192 Wed Sep 30 09:49:59 KST 2009
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: MEP6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C64XX: PLL settings, A=532000000, M=532000000, E=24000000
S3C64XX: HCLKx2=266000000, HCLK=133000000, PCLK=66500000
mout_apll: source is fout_apll (1), rate is 532000000
mout_epll: source is fout_epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
usb-host-bus: source is mout_epll (0), rate is 24000000
uclk1: source is dout_mpll (1), rate is 66500000
spi-bus: source is mout_epll (0), rate is 24000000
spi-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
s3c64xx: 10485760 bytes SDRAM reserved for fimc at 0x50662000
s3c64xx: 8388608 bytes SDRAM reserved for pp at 0x51062000
s3c64xx: 8388608 bytes SDRAM reserved for tv at 0x51862000
s3c64xx: 4194304 bytes SDRAM reserved for jpeg at 0x52062000
s3c64xx: 1048576 bytes SDRAM reserved for cmm at 0x52462000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: init=/init root=/dev/nfs rw nfsroot=192.168.100.3:/root/rootfs/gst-android,timeo=14,retrans=6 ip=192.168.100.4:192.168.100.1:192.168.100.3:255.255.255.0::eth0:off console=ttySAC0,115200n81 ethaddr=00:40:5c:26:0a:5b
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 92544KB available (4076K code, 863K data, 504K init)
bootloader를 제가 드린 bootloader로 해보시기 바랍니다.
어떤 세팅이 틀려져서, samsung original걸로는 부팅이 안되더라고요...쩝