기존 이솝 임베디드 포럼의 지식인 서비스가 게시판 형태로 변경되었습니다.
글 수 6,368
U-Boot 1.1.2 (Dec 24 2005 - 16:09:01)
U-Boot code: 33C00000 -> 33C3FC50 BSS: -> 33C794F0
RAM Configuration:
Bank #0: 30000000 64 MB
Get flash bank 0 size @ 0x0
Total Flash bank's sizes: 0x200000
protect monitor 3fc50 bytes @ address 0
Flash: 2 MB
NAND:64 MB
In: serial
Out: serial
Err: serial
SD Initialize fail..
Hit any key to stop autoboot: 0
TFTP from server 192.168.0.15; our IP address is 192.168.0.20
Filename 'aesopk'.
Load address: 0x32000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
####
done
Bytes transferred = 1350989 (149d4d hex)
## Booting image at 32000000 ...
Image Name: Linux-2.6.13-h1940-aesop2440
Created: 2006-05-02 3:19:49 UTC
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 1350925 Bytes = 1.3 MB
Load Address: 30008000
Entry Point: 30008000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.6.13-h1940-aesop2440 (root@aesop) (gcc version 3.3.4) #2 Tue May 2 12:14:08 KST 2006
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
Machine: aESOP-2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C2440: core 399.651 MHz, memory 133.217 MHz, peripheral 66.608 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.15:/scratchbox/users/aesop/targets/AESOP ip=192.168.0.20:192.168.0.15:192.168.0.1:255.255.255.0::eth0:off console=ttySAC0,115200n81 ethaddr=08:00:3e:26:0a:5b
irq: clearing subpending status 00000002
PID hash table entries: 512 (order: 9, 8192 bytes)
timer tcon=00500000, tcnt d8d2, tcfg 00000200,00000000, usec 0000170f
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 61824KB available (2248K code, 575K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, UPLL 47.980 MHz
SCSI subsystem initialized
usbcore: registered new driver hub
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
yaffs May 2 2006 12:11:39 Installing.
Initializing Cryptographic API
s3c2410 Backlight Driver Initialized.
Console: switching to colour frame buffer device 96x34
S3C24X0 fb0: s3c2410fb frame buffer device initialize done
GPIO L3 bus interface for S3C2440, installed
S3C2410 RTC, (c) 2004 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
cs89x0:cs89x0_probe(0x0)
PP_addr=0x3000
cs89x0.c: v2.4.3-pre1 Russell Nelson <[email protected]>, Andrew Morton <[email protected]>
eth0: cs8900 rev J found at 0xf8000300
cs89x0: Extended EEPROM checksum bad and no Cirrus EEPROM, relying on command line
cs89x0 media RJ-45, IRQ 53, programmed I/O, MAC 00:00:c0:ff:ee:08
cs89x0_probe1() successful
cs89x0:cs89x0_probe(0x0)
cs89x0: request_region(0xf8000300, 0x10) failed
cs89x0: no cs8900 or cs8920 detected. Be sure to disable PnP with SETUP
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand: mapped registers at c4880000
s3c2410-nand: timing: Tacls 13ns, Twrph0 66ns, Twrph1 39ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 4059 at 0x03f6c000
Creating 1 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x04000000 : "Total nand"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
s3c2410_udc: version 28 Aug 2005
mice: PS/2 mouse device common for all mice
s3c2410-buttons successfully loaded
s3c2410 TouchScreen successfully loaded
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 378 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
mmci-s3c2410: probe: mapped sdi_base=c4e80000 irq=37 irq_cd=62 dma=0.
mmci-s3c2410: initialisation done.
godori: AESOP2440 SOUND driver register
godori: AESOP2440 SOUND driver.........probe
AESOP2440 UDA1341 audio driver initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
eth0: using half-duplex 10Base-T (RJ-45)
MMC: sd_app_op_cond timed out. Probably no SD-Card here.
IP-Config: Complete:
device=eth0, addr=192.168.0.20, mask=255.255.255.0, gw=192.168.0.1,
host=192.168.0.20, domain=, nis-domain=(none),
bootserver=192.168.0.15, rootserver=192.168.0.15, rootpath=
Looking up port of RPC 100003/2 on 192.168.0.15
Looking up port of RPC 100005/1 on 192.168.0.15
VFS: Mounted root (nfs filesystem).
Freeing init memory: 112K
INIT: version 2.86 booting
mount: Mounting /dev/root on / failed: No such file or directory
INIT: Entering runlevel: 3
[: 0: unknown operand
INIT: Id "T0" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
===========================================
dev/pts는 /etc/fstab에 있더군요..
그부분 막었고.. 위에서 멈추네요...
이부분은 새로 rootfs를 만들었을때랑 비슷한 에러네요....
U-Boot code: 33C00000 -> 33C3FC50 BSS: -> 33C794F0
RAM Configuration:
Bank #0: 30000000 64 MB
Get flash bank 0 size @ 0x0
Total Flash bank's sizes: 0x200000
protect monitor 3fc50 bytes @ address 0
Flash: 2 MB
NAND:64 MB
In: serial
Out: serial
Err: serial
SD Initialize fail..
Hit any key to stop autoboot: 0
TFTP from server 192.168.0.15; our IP address is 192.168.0.20
Filename 'aesopk'.
Load address: 0x32000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
####
done
Bytes transferred = 1350989 (149d4d hex)
## Booting image at 32000000 ...
Image Name: Linux-2.6.13-h1940-aesop2440
Created: 2006-05-02 3:19:49 UTC
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 1350925 Bytes = 1.3 MB
Load Address: 30008000
Entry Point: 30008000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.6.13-h1940-aesop2440 (root@aesop) (gcc version 3.3.4) #2 Tue May 2 12:14:08 KST 2006
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
Machine: aESOP-2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C2440: core 399.651 MHz, memory 133.217 MHz, peripheral 66.608 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.15:/scratchbox/users/aesop/targets/AESOP ip=192.168.0.20:192.168.0.15:192.168.0.1:255.255.255.0::eth0:off console=ttySAC0,115200n81 ethaddr=08:00:3e:26:0a:5b
irq: clearing subpending status 00000002
PID hash table entries: 512 (order: 9, 8192 bytes)
timer tcon=00500000, tcnt d8d2, tcfg 00000200,00000000, usec 0000170f
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 61824KB available (2248K code, 575K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, UPLL 47.980 MHz
SCSI subsystem initialized
usbcore: registered new driver hub
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
yaffs May 2 2006 12:11:39 Installing.
Initializing Cryptographic API
s3c2410 Backlight Driver Initialized.
Console: switching to colour frame buffer device 96x34
S3C24X0 fb0: s3c2410fb frame buffer device initialize done
GPIO L3 bus interface for S3C2440, installed
S3C2410 RTC, (c) 2004 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
cs89x0:cs89x0_probe(0x0)
PP_addr=0x3000
cs89x0.c: v2.4.3-pre1 Russell Nelson <[email protected]>, Andrew Morton <[email protected]>
eth0: cs8900 rev J found at 0xf8000300
cs89x0: Extended EEPROM checksum bad and no Cirrus EEPROM, relying on command line
cs89x0 media RJ-45, IRQ 53, programmed I/O, MAC 00:00:c0:ff:ee:08
cs89x0_probe1() successful
cs89x0:cs89x0_probe(0x0)
cs89x0: request_region(0xf8000300, 0x10) failed
cs89x0: no cs8900 or cs8920 detected. Be sure to disable PnP with SETUP
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand: mapped registers at c4880000
s3c2410-nand: timing: Tacls 13ns, Twrph0 66ns, Twrph1 39ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 4059 at 0x03f6c000
Creating 1 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x04000000 : "Total nand"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
s3c2410_udc: version 28 Aug 2005
mice: PS/2 mouse device common for all mice
s3c2410-buttons successfully loaded
s3c2410 TouchScreen successfully loaded
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 378 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
mmci-s3c2410: probe: mapped sdi_base=c4e80000 irq=37 irq_cd=62 dma=0.
mmci-s3c2410: initialisation done.
godori: AESOP2440 SOUND driver register
godori: AESOP2440 SOUND driver.........probe
AESOP2440 UDA1341 audio driver initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
eth0: using half-duplex 10Base-T (RJ-45)
MMC: sd_app_op_cond timed out. Probably no SD-Card here.
IP-Config: Complete:
device=eth0, addr=192.168.0.20, mask=255.255.255.0, gw=192.168.0.1,
host=192.168.0.20, domain=, nis-domain=(none),
bootserver=192.168.0.15, rootserver=192.168.0.15, rootpath=
Looking up port of RPC 100003/2 on 192.168.0.15
Looking up port of RPC 100005/1 on 192.168.0.15
VFS: Mounted root (nfs filesystem).
Freeing init memory: 112K
INIT: version 2.86 booting
mount: Mounting /dev/root on / failed: No such file or directory
INIT: Entering runlevel: 3
[: 0: unknown operand
INIT: Id "T0" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
===========================================
dev/pts는 /etc/fstab에 있더군요..
그부분 막었고.. 위에서 멈추네요...
이부분은 새로 rootfs를 만들었을때랑 비슷한 에러네요....
다시 올리던가 하겠습니다.