회원 및 비회원 모두 열람이 가능합니다. 최대 업로드 가능한 용량은 20MB 입니다.
글 수 1,910
안녕하세요? 현재 이솝 보드용으로 Kernel 2.6.29를 올리고 있습니다.
구글의 안드로이드 커널을 기본으로 작업 중에 있으며, 최종적으로는 2.6.29 커널 하나만을 가지고,
이솝 포럼에 공개되어 있는 Linux용 RFS와 Android용 RFS를 모두 구동 시킬 수 있는 커널을 제작
하는 것이 목표 입니다. 아직 작업 중이지만 부팅로그 올려드릴께요... :)
이더넷하고, 사운드, OTG... 아직 수정해야 할 부분이 많네요. ㅎㅎ
U-Boot 1.1.6 (Mar 31 2009 - 10:54:38) for AESOP6410
CPU: S3C6410@666MHz
Fclk = 666MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (ASYNC Mode)
Board: AESOP-S3C6410
DRAM: 128 MB
Flash: 0 kB
NAND: 256 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
smc911x: initializing
smc911x: detected LAN9215 controller
smc911x: phy initialized
smc911x: MAC 00:40:5c:26:0a:5b
TFTP from server 192.168.1.15; our IP address is 192.168.1.100
Filename 'zImage'.
Load address: 0xc0008000
Loading: T #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############
done
Bytes transferred = 1728892 (1a617c hex)
Boot with zImage
Starting kernel ...
Uncompressing Linux................................................................................................................. done, booting the kernel.
Linux version 2.6.29 (jhkim@jhkim-Xeon) (gcc version 4.2.4) #95 Fri Apr 17 16:40:02 KST 2009
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDK6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C64XX: PLL settings, A=666000000, M=532000000, E=24000000
S3C64XX: HCLKx2=266000000, HCLK=133000000, PCLK=66500000
mout_apll: source is fout_apll (1), rate is 666000000
mout_epll: source is fout_epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
usb-host-bus: source is mout_epll (0), rate is 24000000
uclk1: source is dout_mpll (1), rate is 66500000
spi-bus: source is mout_epll (0), rate is 24000000
spi-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttySAC0,115200 root=/dev/nfs rw nfsroot=192.168.1.15:/nfsroot/RootFS-aESOP6410 ip=192.168.1.85:192.168.1.15:192.168.1.1:255.255.255.0::eth0:off mem=128M ethaddr=00:40:5c:26:0a:5b
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125980KB available (3160K code, 432K data, 160K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 665.19 BogoMIPS (lpj=3325952)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 564 bytes
NET: Registered protocol family 16
S3C6410: Initialising architecture
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
bio: create slab <bio-0> at 0
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 4, 81920 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 246
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
S3C_LCD clock got enabled :: 133.000 Mhz
LCD TYPE :: LMS350DF01 will be initialized
GPIO-18 autorequested
GPIO-19 autorequested
power on sequence done...
display on sequence done...
Window[0] - FB1: map_video_memory: clear ff000000:00096000
FB1: map_video_memory: dma=57a00000 cpu=ff000000 size=00096000
Window[0] - FB2: map_video_memory: clear ff04b000:0004b000
FB2: map_video_memory: dma=57a4b000 cpu=ff04b000 size=0004b000
Console: switching to colour frame buffer device 40x30
fb0: s3cfb frame buffer device
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
brd: module loaded
loop: module loaded
eth0 (smc911x): not using net_device_ops yet
eth0: LAN9215 (rev 0) at 0x18000000 IRQ 104
eth0: Ethernet addr: 00:09:c0:ff:ec:48
Driver 'sd' needs updating - please use bus_type methods
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using software ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "Bootloader"
0x000000040000-0x000000400000 : "Kernel"
0x000000400000-0x000010000000 : "File System"
mice: PS/2 mouse device common for all mice
S3C Touchscreen driver, (c) 2008 Samsung Electronics
S3C TouchScreen got loaded successfully : 12 bits
input: S3C TouchScreen as /class/input/input0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c.0: slave address 0x10
s3c2440-i2c s3c2440-i2c.0: bus frequency set to 377 KHz
at24 0-0050: 1024 byte 24c08 EEPROM (writable)
s3c2440-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
s3c2440-i2c s3c2440-i2c.1: slave address 0x10
s3c2440-i2c s3c2440-i2c.1: bus frequency set to 377 KHz
at24 1-0057: 16384 byte 24c128 EEPROM (writable)
s3c2440-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using DMA
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
Advanced Linux Sound Architecture Driver Version 1.0.18a.
ALSA device list:
No soundcards found.
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
eth0: link down
IP-Config: Complete:
device=eth0, addr=192.168.1.85, mask=255.255.255.0, gw=192.168.1.1,
host=192.168.1.85, domain=, nis-domain=(none),
bootserver=192.168.1.15, rootserver=192.168.1.15, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.15
eth0: link up, 100Mbps, half-duplex, lpa 0xCDE1
Looking up port of RPC 100005/1 on 192.168.1.15
VFS: Mounted root (nfs filesystem) on device 0:12.
Freeing init memory: 160K
udevd version 124 started
INIT: Entering runlevel: 5
Starting Dropbear SSH server: dropbear.
Starting system message bus: dbus.
Starting syslogd/klogd: done
Starting Connection Manager
Starting GPE display manager: gpe-dm
_____ _____ _____ _____ _____
| _ | __| __| | _ |
| | __|__ | | | __|
|__|__|_____|_____|_____|__|.or.kr
(C)2009 aESOP Embedded Forum.
aESOP S3C6410 Embedded Linux Platform.
System : aESOP-S3C6410
Console : s3c2410_serial0
aESOP-S3C6410 login: root
root@aESOP-S3C6410:~#
구글의 안드로이드 커널을 기본으로 작업 중에 있으며, 최종적으로는 2.6.29 커널 하나만을 가지고,
이솝 포럼에 공개되어 있는 Linux용 RFS와 Android용 RFS를 모두 구동 시킬 수 있는 커널을 제작
하는 것이 목표 입니다. 아직 작업 중이지만 부팅로그 올려드릴께요... :)
이더넷하고, 사운드, OTG... 아직 수정해야 할 부분이 많네요. ㅎㅎ
U-Boot 1.1.6 (Mar 31 2009 - 10:54:38) for AESOP6410
CPU: S3C6410@666MHz
Fclk = 666MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (ASYNC Mode)
Board: AESOP-S3C6410
DRAM: 128 MB
Flash: 0 kB
NAND: 256 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
smc911x: initializing
smc911x: detected LAN9215 controller
smc911x: phy initialized
smc911x: MAC 00:40:5c:26:0a:5b
TFTP from server 192.168.1.15; our IP address is 192.168.1.100
Filename 'zImage'.
Load address: 0xc0008000
Loading: T #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#############
done
Bytes transferred = 1728892 (1a617c hex)
Boot with zImage
Starting kernel ...
Uncompressing Linux................................................................................................................. done, booting the kernel.
Linux version 2.6.29 (jhkim@jhkim-Xeon) (gcc version 4.2.4) #95 Fri Apr 17 16:40:02 KST 2009
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDK6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C64XX: PLL settings, A=666000000, M=532000000, E=24000000
S3C64XX: HCLKx2=266000000, HCLK=133000000, PCLK=66500000
mout_apll: source is fout_apll (1), rate is 666000000
mout_epll: source is fout_epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
usb-host-bus: source is mout_epll (0), rate is 24000000
uclk1: source is dout_mpll (1), rate is 66500000
spi-bus: source is mout_epll (0), rate is 24000000
spi-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttySAC0,115200 root=/dev/nfs rw nfsroot=192.168.1.15:/nfsroot/RootFS-aESOP6410 ip=192.168.1.85:192.168.1.15:192.168.1.1:255.255.255.0::eth0:off mem=128M ethaddr=00:40:5c:26:0a:5b
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125980KB available (3160K code, 432K data, 160K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 665.19 BogoMIPS (lpj=3325952)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 564 bytes
NET: Registered protocol family 16
S3C6410: Initialising architecture
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
bio: create slab <bio-0> at 0
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 4, 81920 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 246
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
S3C_LCD clock got enabled :: 133.000 Mhz
LCD TYPE :: LMS350DF01 will be initialized
GPIO-18 autorequested
GPIO-19 autorequested
power on sequence done...
display on sequence done...
Window[0] - FB1: map_video_memory: clear ff000000:00096000
FB1: map_video_memory: dma=57a00000 cpu=ff000000 size=00096000
Window[0] - FB2: map_video_memory: clear ff04b000:0004b000
FB2: map_video_memory: dma=57a4b000 cpu=ff04b000 size=0004b000
Console: switching to colour frame buffer device 40x30
fb0: s3cfb frame buffer device
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
brd: module loaded
loop: module loaded
eth0 (smc911x): not using net_device_ops yet
eth0: LAN9215 (rev 0) at 0x18000000 IRQ 104
eth0: Ethernet addr: 00:09:c0:ff:ec:48
Driver 'sd' needs updating - please use bus_type methods
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using software ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000040000 : "Bootloader"
0x000000040000-0x000000400000 : "Kernel"
0x000000400000-0x000010000000 : "File System"
mice: PS/2 mouse device common for all mice
S3C Touchscreen driver, (c) 2008 Samsung Electronics
S3C TouchScreen got loaded successfully : 12 bits
input: S3C TouchScreen as /class/input/input0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c.0: slave address 0x10
s3c2440-i2c s3c2440-i2c.0: bus frequency set to 377 KHz
at24 0-0050: 1024 byte 24c08 EEPROM (writable)
s3c2440-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
s3c2440-i2c s3c2440-i2c.1: slave address 0x10
s3c2440-i2c s3c2440-i2c.1: bus frequency set to 377 KHz
at24 1-0057: 16384 byte 24c128 EEPROM (writable)
s3c2440-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using DMA
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
s3c6410_setup_sdhci0_cfg_card: CTRL 2=c0004100, 3=80808080
Advanced Linux Sound Architecture Driver Version 1.0.18a.
ALSA device list:
No soundcards found.
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
eth0: link down
IP-Config: Complete:
device=eth0, addr=192.168.1.85, mask=255.255.255.0, gw=192.168.1.1,
host=192.168.1.85, domain=, nis-domain=(none),
bootserver=192.168.1.15, rootserver=192.168.1.15, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.15
eth0: link up, 100Mbps, half-duplex, lpa 0xCDE1
Looking up port of RPC 100005/1 on 192.168.1.15
VFS: Mounted root (nfs filesystem) on device 0:12.
Freeing init memory: 160K
udevd version 124 started
INIT: Entering runlevel: 5
Starting Dropbear SSH server: dropbear.
Starting system message bus: dbus.
Starting syslogd/klogd: done
Starting Connection Manager
Starting GPE display manager: gpe-dm
_____ _____ _____ _____ _____
| _ | __| __| | _ |
| | __|__ | | | __|
|__|__|_____|_____|_____|__|.or.kr
(C)2009 aESOP Embedded Forum.
aESOP S3C6410 Embedded Linux Platform.
System : aESOP-S3C6410
Console : s3c2410_serial0
aESOP-S3C6410 login: root
root@aESOP-S3C6410:~#
인생은 연극이고 세상은 무대이다!
이솝 임베디드 포럼 운영 및 비즈니스와 관련된 것 이외에 E-Mail이나 메신저 및 휴대폰 등을 통한 개인적인 질문 및 답변은 받지 않습니다. 문의 사항은 이솝 임베디드 포럼 게시판을 이용해 주시면 감사하겠습니다.
역쉬 사람들은 다양하대니깐요...ㅎ