AESOP Embedded Forum : 자유게시판 - Magiceyes MP2530(mmsp2+) linuxkernel 2.6.20 ramdisk부팅 완료.

Favorites

자유게시판 : 포럼 회원님들 간의 자유로운 각종 정보 교류를 위한 게시판 입니다.

회원 및 비회원 모두 열람이 가능합니다. 최대 업로드 가능한 용량은 20MB 입니다.

글 수 1,910

Magiceyes MP2530(mmsp2+) linuxkernel 2.6.20 ramdisk부팅 완료.

조회 수 8925 추천 수 0 2007.04.03 00:31:53

김정한 *.173.154.76 http://www.aesop.or.kr/index.php?mid=Board_Community_Freeboard&document_srl=6576

사실 ramdisk 잡은지 조금 됐습니다..
이것저것 정신이 없어서 글을 늦게 올립니다..

printk 세상에 도달한 이상 나머지 포팅들도
일사천리로 진행되리라 기대합니다^^

같이 수고하신
현철이형 장호형 현진이형 감사합니다.

조만간 또 진행 사항 올리겠습니다.
=================================

MP2530(MMSP2+) linux kernel 2.6.20 부팅성공했습니다.

U-Boot 1.1.6 (Apr  2 2007 - 15:33:41)

U-Boot code: 03F00000 -> 03F8B924  BSS: -> 03F953C0
RAM Configuration:
Bank #0: 00000000 64 MB
NAND:  64 MiB
nand_read_ecc: from = 0x00088000, len = 1024
nand_read_ecc: Failed ECC read, page 0x00000440
nand_read_ecc: Failed ECC read, page 0x00000440
nand_read_ecc: Failed ECC read, page 0x00000441
nand_read_ecc: Failed ECC read, page 0x00000441
*** Warning - bad CRC or NAND, using default environment

In:    serial
Out:   serial
Err:   serial
enetaddr :
### main_loop entered: bootdelay=3

### main_loop: bootcmd="tftp 02000000 mp2530;tftp 01000000 rd2530.img;bootm 02000000 01000000"
Hit any key to stop autoboot:  0
TFTP from server 172.16.1.200; our IP address is 172.16.1.100
Filename 'mp2530'.
Load address: 0x2000000
Loading: #################################################################
         #################################################################
         #################################################################
         #########################################################
done
Bytes transferred = 1289095 (13ab87 hex)
TFTP from server 172.16.1.200; our IP address is 172.16.1.100
Filename 'rd2530.img'.
Load address: 0x1000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ##############
done
Bytes transferred = 8388672 (800040 hex)
## Booting image at 02000000 ...
   Image Name:   Linux-2.6.20
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    1289031 Bytes =  1.2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Loading Ramdisk Image at 01000000 ...
   Image Name:   Ramdisk
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8388608 Bytes =  8 MB
   Load Address: 00800000
   Entry Point:  00800000
   Verifying Checksum ... OK
## Transferring control to Linux (at address 00008000) ...

Starting kernel ...

Linux version 2.6.20 ([email protected]) (gcc version 3.4.5) #268 Mon Apr 2 15:36:49 KST 2007
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: AESOP2530
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/ram0 rw rootfstype=ext2 ip=172.16.1.101:172.16.1.200:172.16.1.1:255.255.255.0::eth0:off console=ttySAC3,115200n81
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
config: 8bits/char
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 53924KB available (2400K code, 259K data, 96K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
MP2530: Initialising architecture
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 8192K
NetWinder Floating Point Emulator V0.97 (double precision)
Installing knfsd (copyright (C) 1996 [email protected]).
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
mp2530-uart.0: mp2530_serial0 at MMIO 0xf0016000 (irq = 42) is a MP2530
mp2530-uart.1: mp2530_serial1 at MMIO 0xf0016080 (irq = 46) is a MP2530
mp2530-uart.2: mp2530_serial2 at MMIO 0xf0016800 (irq = 50) is a MP2530
mp2530-uart.3: mp2530_serial3 at MMIO 0xf0016880 (irq = 54) is a MP2530
mp2530-uart.4: mp2530_serial4 at MMIO 0xf0017000 (irq = 58) is a MP2530
mp2530-uart.5: mp2530_serial5 at MMIO 0xf0017080 (irq = 62) is a MP2530
RAMDISK driver initialized: 1 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
usbmon: debugfs is not available
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
IP-Config: Device `eth0' not found.
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 8192KiB [1 disk] into ram disk... done.
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 96K
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
## mp2530_serial_set_termios
config: 8bits/char
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
INIT: ## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
version 2.86 booting## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
## mp2530_serial_set_termios
config: 8bits/char
Initializing udev dynamic device directory.
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
/etc/rc.d/rc.S: 47: /root/glogo: not found
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
mount: ## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
Mounting /dev/root on / failed: No such file or directory
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55
mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
INIT: ## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
Entering runlevel: 3## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
##1 mp2530_serial_stop_rx: port=c028d334
##2 mp2530_serial_stop_rx: port=c028d334
mp2530_serial_startup: port=0x08f0016880 (0x08f0016880)
mp2530_serial_startup hwport 3, rxirq = 55

mp2530_serial_startup hwport 3, txirq = 54
mp2530_serial_startup ok
## mp2530_serial_set_termios
config: 8bits/char
## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
Starting sysklogd daemons:  ## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
/sbin/syslogd## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
/sbin/klogd -c 3## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2

## mp2530_serial_stop_tx 1
## mp2530_serial_stop_tx 2
[: 0: unknown operand

AESOP Linux

/) /)
(='.'=) <- godori

root@godori:~#

이 게시물을

엮인글 :: http://www.aesop.or.kr/index.php?mid=Board_Community_Freeboard&document_srl=6576&act=trackback&key=9a1

고도리

2007.04.03 00:39:12
*.70.26.87

디버깅 로그의 압박.....godori란 글자가 이렇게 반가울수가...ㅎㅎ

정말 수고했다.....거의 매일 밤샘하다시피한 보람이 있넹...

앞으로 노가다만 남았넹....^^

이장호

2007.04.03 03:07:07
*.70.26.87

현철형님 정한님 현진님 고생 하셨습니다 ... 밤새도록 작업하시고 또 회사나가시고
저희들에게 교육해주시고 현철형님 너무 멋지십니다 ^^

김경호

2007.04.03 07:29:20
*.235.223.81

로그 보고 궁금한데요...
serial이 0~5번 6개인가요?
lx800에 이은 다른 이솝보드가 등장하길 기대 하겠습니다.~

김정한

2007.04.03 08:12:27
*.173.154.76

mp2530은 UART 채널이 6개입니다^^

List of Articles

번호	제목	글쓴이	날짜	조회 수
공지	교육 홍보 및 광고는 "교육 및 세미나 홍보" 게시판을 이용해 ...	관리자	2010-07-15	108026
Ubuntu 18.04 소식 [6] 이제현 2018-05-02 조회 수 1204
샤오미 AI 스피커를 분해해봤습니다. [7] 천동이 2018-04-10 조회 수 697
설문조사 - 오프라인 강의한다면 참여 의사가 있는 강의 투표에... 천동이 2018-04-09 조회 수 376
DSRC 대역에서 Ping6 관련 질문 [15] 김증일 2018-03-20 조회 수 536
이메일 인증 처리 문제. [2] 유형목 2018-03-19 조회 수 146
[RK3399] Odroid-N1 소스가 링크에 보이네요. [2] 고도리 2018-03-19 조회 수 331
[RK3399] FireFly 169불 주고 샀어요. 근데 [1] 김민욱 2018-03-12 조회 수 339
[서버이전] 우분투 10.04 ->16.04로 OS 교체 및 가상화처리... [1] 유형목 2018-03-12 조회 수 468
2018 년 어떤 아이템으로 사업해야 하나 ? 파란새 2018-03-08 조회 수 311
봄이 왔군요.. [3] 이제현 2018-03-08 조회 수 262
[S5P6818/NXP4330] 개발보드(ALTO-S) - Camera(serdes) 지원 ... [3] 고도리 2018-03-02 조회 수 751
[RK3399] Firefly AIO-3399J 보드 [2] 고도리 2018-03-01 조회 수 541
[RK3399] open source hardware 추천 요청 [2] 김민욱 2018-02-26 조회 수 313
[RK3399 Ev-kit] 작년 중반에 중국 친구가 보내줬던 보드 [14] 고도리 2018-02-20 조회 수 1165
운영자님 ... 이솝 2018 년 운영계획 있으시면 부탁드립니다 .... [3] 파란새 2017-12-31 조회 수 388
다사다난한 2017년이 져 물어 갑니다 ... [3] 파란새 2017-12-16 조회 수 300
잉여력 폭발. [5] Jazzguitar 2017-11-09 조회 수 475
10월에 aesop 사이트 접속이 안돼서 궁금했습니다 [7] QueenBee 2017-11-03 조회 수 330
이맥스 책을 찾고 있습니다. 서연석 2017-09-30 조회 수 216
Kernel 4.14 RC1이 나왔네요.. [7] 이제현 2017-09-18 조회 수 1455

번호

제목

글쓴이

날짜