ODROID-A 시생산이 차주 월요일부터 시작되고, 본격적인 생산은 4월 6일 정도로 예상합니다.

배송은 11일부 시작되고요~~

그리고 현재 판매 상태로 보면, 28일 정도면 1차 예약 판매가 종료될것 같습니다.

아래는 듀얼코어 Exynos 4210의 부팅 로그입니다. 부트로더,커널,안드로이드 포함입니다.

그리고 ARM core뿐 아니라 Mali-400까지도 DVFS가 동작하고 있습니다.

1Gbyte Hi-mem 5개 세그먼트가 모두 동작하여 광활한 메모리 공간을 즐길 수 있습니다.

몇년전만 하더라도 임베디드 시스템에서 1Gbyte를 사용하는 날이 이렇게 빨리 올줄은 상상도 못했습니다.

더군다나 C110/V210의 2배인 800Mega Data 전송 속도입니다.

그리고 CDC를 이용해서 3G모뎀과 GPS 드라이버가 함께 올라가는것도 찾으실 수 있을겁니다.

자이로스코프, 지자기센서, 가속도센서 9축 드라이버도 등록됩니다.

그 밖에도 재미있는 내용들이 있으니, 숨은그림찾기 놀이 한번 해보세요. ^.^

지금은 디버깅 정보가 많이 포함되어 좀 지저분 합니다. 정리가 필요하네요.

앞으로 공개가 얼마 않남았으니 기대해 주세요~~

U-Boot 2010.03 ( 3? 16 2011 - 19:41:02) for HKDKC210 Android

APLL = 1000MHz, MPLL = 800MHz
PMIC:
Board:  hkdkc210
EVT1 POP_B
DRAM:    1 GB
MMC:    7639 MB
*** Warning - using default environment

In:    serial
Out:   serial
Err:   serial


Checking Boot Mode ... SDMMC
board_late_init
Hit any key to stop autoboot:  0
reading kernel.. 1089, 8192
MMC read: dev # 0, block # 1089, count 8192 ...8192 blocks read: OK
completed
reading RFS.. 9281, 2048
MMC read: dev # 0, block # 9281, count 2048 ...2048 blocks read: OK
completed
Boot with zImage
## Loading init Ramdisk from Legacy Image at 40a00000 ...
   Image Name:   ramdisk
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    306407 Bytes = 299.2 kB
   Load Address: 40800000
   Entry Point:  40800000

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.35.7 (codewalker@codewalker-desktop) (gcc vers1
[    0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ce
[    0.000000] Machine: ODROIDA
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU S5PV310 (id 0x43210210)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] s3c_register_clksrc: clock armclk has no registers set
[    0.000000] mout_audss: bad source 0
[    0.000000] S5PV310: ARMCLK=1000000000, DMC=400000000, ACLK200=200000000
[    0.000000] ACLK100=100000000, ACLK160=160000000, ACLK133=133333333
[    0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[    0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[    0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[    0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[    0.000000] uclk1: source is mout_mpll (6), rate is 100000000
[    0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_csis: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_csis: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_cam0: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_cam1: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_mixer: source is sclk_dac (0), rate is 24000000
[    0.000000] sclk_fimd: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_fimd: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_sata: source is mout_mpll (0), rate is 133333333
[    0.000000] sclk_spi: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_spi: source is mout_mpll (6), rate is 80000000
[    0.000000] sclk_spi: source is xusbxti (1), rate is 24000000
[    0.000000] sclk_fimg2d: source is mout_g2d0 (0), rate is 100000000
[    0.000000] sclk_mfc: source is mout_mfc0 (0), rate is 200000000
[    0.000000] sclk_g3d: source is mout_g3d0 (0), rate is 166666666
[    0.000000] sclk_pwi: source is xusbxti (1), rate is 12000000
[    0.000000] mem infor: bank0 start-> 0x40000000, bank0 size-> 0x10000000
[    0.000000] bank1 start-> 0x50000000, bank1 size-> 0x10000000
[    0.000000] CMA reserve : fimd, addr is 0x4f100000, size is 0xf00000
[    0.000000] CMA reserve : mfc0, addr is 0x4cd00000, size is 0x2400000
[    0.000000] CMA reserve : mfc1, addr is 0x4a900000, size is 0x2400000
[    0.000000] CMA reserve : fimc0, addr is 0x49a00000, size is 0xf00000
[    0.000000] CMA reserve : fimc1, addr is 0x48b00000, size is 0xf00000
[    0.000000] CMA reserve : fimc2, addr is 0x47300000, size is 0x1800000
[    0.000000] CMA reserve : fimc3, addr is 0x46d00000, size is 0x600000
[    0.000000] CMA reserve : jpeg, addr is 0x46500000, size is 0x800000
[    0.000000] CMA reserve : fimg2d, addr is 0x45cff800, size is 0x800800
[    0.000000] CMA reserve : (null), addr is 0x45cff800, size is 0x0
[    0.000000] PERCPU: Embedded 7 pages/cpu @d9406000 s5888 r8192 d14592 u65536
[    0.000000] pcpu-alloc: s5888 r8192 d14592 u65536 alloc=16*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pa6
[    0.000000] Kernel command line: console=ttySAC1,115200 consoleblank=0
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 256MB 256MB 128MB 128MB 256MB = 1024MB total
[    0.000000] Memory: 865328k/865328k available, 183248k reserved, 393216K higm
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xff600000 - 0xffe00000   (   8 MB)
[    0.000000]     vmalloc : 0xe8800000 - 0xf0000000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe8000000   ( 640 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0032000   ( 168 kB)
[    0.000000]       .text : 0xc0032000 - 0xc05a2000   (5568 kB)
[    0.000000]       .data : 0xc05c2000 - 0xc060b8e0   ( 295 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, 1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU-based detection of stalled CPUs is disabled.
[    0.000000]  Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:396
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttySAC1] enabled
[    0.449787] Calibrating delay loop... 1992.29 BogoMIPS (lpj=4980736)
[    0.580046] pid_max: default: 32768 minimum: 301
[    0.581847] Mount-cache hash table entries: 512
[    0.586651] CPU: Testing write buffer coherency: ok
[    0.591295] L310 cache controller enabled
[    0.595161] l2x0: 16 ways, CACHE_ID 0x4100c4c5, AUX_CTRL 0x7e470001, Cache SB
[    0.605022] >made stopper
[    0.615019] >made stopper
[    0.625083] CPU1: Booted secondary processor
[    0.625138] Brought up 2 CPUs
[    0.626711] SMP: Total of 2 processors activated (3984.58 BogoMIPS).
[    0.636991] regulator: core version 0.5
[    0.637156] NET: Registered protocol family 16
[    0.641984] S3C Power Management, Copyright 2004 Simtec Electronics
[    0.647574] s3c_rtc_base: e8808000
[    0.654472] S5PV310: Initializing architecture
[    0.655890] samsung-pd samsung-pd.0: power domain registered
[    0.661061] samsung-pd samsung-pd.1: power domain registered
[    0.666660] samsung-pd samsung-pd.2: power domain registered
[    0.672301] samsung-pd samsung-pd.3: power domain registered
[    0.677943] samsung-pd samsung-pd.5: power domain registered
[    0.683584] samsung-pd samsung-pd.6: power domain registered
[    0.689227] samsung-pd samsung-pd.4: power domain registered
[    0.694967] s3c24xx-pwm s3c24xx-pwm.0: tin at 100000000, tdiv at 100000000, 0
[    0.703848] UMP: UMP device driver 255M loaded
[    0.718359] bio: create slab <bio-0> at 0
[    0.719324] SCSI subsystem initialized
[    0.721068] usbcore: registered new interface driver usbfs
[    0.726209] usbcore: registered new interface driver hub
[    0.731344] usbcore: registered new device driver usb
[    0.736904] i2c-gpio i2c-gpio.1: using pins 44 (SDA) and 45 (SCL)
[    0.742531] i2c-gpio i2c-gpio.2: using pins 6 (SDA) and 7 (SCL)
[    0.748380] s3c-i2c s3c2440-i2c.0: slave address 0x10
[    0.753278] s3c-i2c s3c2440-i2c.0: bus frequency set to 97 KHz
[    0.798067] regulator: VDD_ADC_3.3V: 3300 mV
[    0.800081] regulator: VALIVE_1.1V: 1100 mV
[    0.802987] regulator: VUOTG_D_1.1V/VUHOST_D_1.1V: 1100 mV
[    0.808548] regulator: V_MIPI_1.8V: 1800 mV
[    0.812802] regulator: VDD_MIF_1.8V: 1800 mV
[    0.817152] regulator: VDD_CAM_1.8V: 1800 mV
[    0.821472] regulator: VDD_GPS_1.8V: 1800 mV
[    0.825817] regulator: VUOTG_A_3.3V/VUHOST_A_3.3V: 3300 mV
[    0.831371] regulator: VDD_LCD_2.8V: 2800 mV
[    0.835709] regulator: VDD_PLL_1.1V: 1100 mV
[    0.840050] regulator: VDD_LDO13: 3000 mV
[    0.844133] regulator: VDD_LDO14: 1800 mV
[    0.848229] regulator: VDD_LDO15: 2800 mV
[    0.852297] regulator: VDD_LDO21: 1500 mV
[    0.855662] regulator: vdd_arm range: 775 <--> 1400 mV at 1200 mV
[    0.861841] regulator: vdd_int range: 750 <--> 1375 mV at 1100 mV
[    0.867280] regulator: vdd_g3d range: 900 <--> 1200 mV at 950 mV
[    0.874800] regulator: VDD_IO_1.8V: 1800 mV
[    0.877937] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[    0.882979] Advanced Linux Sound Architecture Driver Version 1.0.23.
[    0.889200] Bluetooth: Core ver 2.15
[    0.892454] NET: Registered protocol family 31
[    0.896779] Bluetooth: HCI device and connection manager initialized
[    0.903150] Bluetooth: HCI socket layer initialized
[    0.907990] Switching to clocksource mct-frc
[    0.928572] NET: Registered protocol family 2
[    0.928677] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.934632] TCP established hash table entries: 131072 (order: 8, 1048576 by)
[    0.943286] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[    0.949239] TCP: Hash tables configured (established 131072 bind 65536)
[    0.954984] TCP reno registered
[    0.958098] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.964034] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.970465] NET: Registered protocol family 1
[    0.974803] Trying to unpack rootfs image as initramfs...
[    0.998289] Freeing initrd memory: 296K
[    0.998667] PMU: registered new PMU device of type 0
[    1.001724] --------------------------------------------------------
[    1.007817]
[    1.007820] hkc1xx_sysfs_init(362) : Sleep Disable Flag SET!!(Wake_lock_init)
[    1.007824]
[    1.017845] --------------------------------------------------------
[    1.024766] Loaded driver for PL330 DMAC-1 s3c-pl330
[    1.029159]  DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    1.035368] Loaded driver for PL330 DMAC-2 s3c-pl330
[    1.040244]  DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    1.057036] highmem bounce pool size: 64 pages
[    1.057332] ashmem: initialized
[    1.059233] NTFS driver 2.1.29 [Flags: R/W DEBUG].
[    1.063815] ROMFS MTD (C) 2007 Red Hat, Inc.
[    1.068014] msgmni has been set to 922
[    1.071975] alg: No test for fcrypt (fcrypt-generic)
[    1.076858] alg: No test for stdrng (krng)
[    1.080779] io scheduler noop registered
[    1.084672] io scheduler deadline registered
[    1.088924] io scheduler cfq registered (default)
[    1.117585] Console: switching to colour frame buffer device 170x48
[    1.131625] FIMD src sclk = 114285714
[    1.134766] s3cfb s3cfb.0: registered successfully
[    1.231280] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.233297] s5pv210-uart.0: s3c2410_serial0 at MMIO 0x13800000 (irq = 16) is0
[    1.240494] s5pv210-uart.1: s3c2410_serial1 at MMIO 0x13810000 (irq = 20) is0
[    1.248600] s5pv210-uart.2: s3c2410_serial2 at MMIO 0x13820000 (irq = 24) is0
[    1.256721] s5pv210-uart.3: s3c2410_serial3 at MMIO 0x13830000 (irq = 28) is0
[    1.264868] s5pv210-uart.4: s3c2410_serial4 at MMIO 0x13840000 (irq = 320) i0
[    1.277598] brd: module loaded
[    1.279803] loop: module loaded
[    1.281610] ish1000 verion is 0xf
[    1.495187] i2c i2c-2: mpu3050: +bma150
[    1.495230] i2c i2c-2: WARNING: Accel irq not assigned
[    1.498494] i2c i2c-2: mpu3050: +ams0303
[    1.502421] i2c i2c-2: WARNING: Compass irq not assigned
[    1.507708] i2c i2c-2: mpu3050: No Pressure Present
[    1.543782] i2c i2c-2: Installing irq using 274
[    1.543832] i2c i2c-2: Module Param interface = mpuirq
[    1.548168]  ==========================================================
[    1.554402]   mtv818 Module Build Date/Time: Mar 24 2011, 10:04:26
[    1.560559]  ==========================================================
[    1.560564]
[    1.569480] [mtv818_spi_probe] ENTERED!!!!!!!!!!!!!!
[    1.603638] Check MTV818 0x00 = 0x8a
[    1.603774] PPP generic driver version 2.4.2
[    1.606168] PPP Deflate Compression module registered
[    1.610950] PPP BSD Compression module registered
[    1.616115] PPP MPPE Compression module registered
[    1.620413] NET: Registered protocol family 24
[    1.624960] usbcore: registered new interface driver asix
[    1.630319] usbcore: registered new interface driver cdc_ether
[    1.636037] cdc_ncm: 30-Nov-2010
[    1.639325] usbcore: registered new interface driver cdc_ncm
[    1.644975] usbcore: registered new interface driver net1080
[    1.650613] usbcore: registered new interface driver cdc_subset
[    1.656514] usbcore: registered new interface driver zaurus
[    1.662000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.668632] s5p-ehci s5p-ehci: s5pv210 EHCI
[    1.672692] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[    1.679781] s5p-ehci s5p-ehci: irq 134, io mem 0x12580000
[    1.693525] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[    1.694056] hub 1-0:1.0: USB hub found
[    1.697013] hub 1-0:1.0: 3 ports detected
[    1.701317] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.707220] [usb_host_phy_init]Already power on PHY
[    1.712044] s5p-ohci s5p-ohci: s5pv210 OHCI
[    1.716222] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2
[    1.723247] s5p-ohci s5p-ohci: irq 134, io mem 0x12590000
[    1.787936] hub 2-0:1.0: USB hub found
[    1.787985] hub 2-0:1.0: 3 ports detected
[    1.790432] usbcore: registered new interface driver cdc_acm
[    1.795686] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems s
[    1.804304] usbcore: registered new interface driver cdc_wdm
[    1.809834] Initializing USB Mass Storage driver...
[    1.814810] usbcore: registered new interface driver usb-storage
[    1.820684] USB Mass Storage support registered.
[    1.825413] s3c-udc : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Eles
[    1.825418] s3c-udc : version 15 March 2009 (DMA Mode)
[    1.838134] android init
[    1.840671] android_probe pdata: c05de5c0
[    1.844732] android_bind
[    1.847317] android_usb gadget: android_usb ready
[    1.851847] Registered gadget driver 'android_usb'
[    1.857741] f_adb init
[    1.858963] android_register_function adb
[    1.862940] f_mass_storage init
[    1.866104] fsg_probe pdev: c05ddba0, pdata: c05de5e4
[    1.871191] android_register_function usb_mass_storage
[    1.876236] f_rndis init
[    1.878859] android_register_function rndis
[    1.882907] rndis_function_bind_config MAC: 00:00:00:00:00:00
[    1.888668] android_usb gadget: using random self ethernet address
[    1.894818] android_usb gadget: using random host ethernet address
[    1.901326] usb0: MAC 86:8e:fe:36:a5:b5
[    1.904803] usb0: HOST MAC 6e:a3:b1:ae:d8:99
[    1.909238] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    1.915906] android_usb gadget: Number of LUNs=1
[    1.920505]  lun0: LUN: removable file: (no medium)
[    1.925467] adb_bind_config
[    1.928904] mice: PS/2 mouse device common for all mice
[    1.933528] hkc1xx_keypad_init
[    1.936666] input: hkc1xx-keypad as /devices/virtual/input/input0
[    1.942471] hkc1xx_keypad_open
[    1.945682] --------------------------------------------------------
[    1.951839] HardKernel : ODROID-C210 Keypad driver initialized!! Ver 1.0
[    1.958525] --------------------------------------------------------
[    1.964864] platform_driver_register 0
[    1.969089] input: hkc1xx-touch as /devices/virtual/input/input1
[    1.982042] TOUCH ID          : 0xD1
[    1.984602] TOUCH SENSITIVITY : 0x3E
[    1.987482] HKC1XX TOUCH request_irq = 353
[    1.987865] --------------------------------------------------------
[    1.994216] HardKernel : ODROID C210 Multi Touch driver(portrait)!! Ver 1.0
[    2.001155] --------------------------------------------------------
[    2.007788] S3C24XX RTC, (c) 2004,2006 Simtec Electronics
[    2.013247] using rtc device, s3c, for alarms
[    2.017064] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[    2.022289] usb 1-1: new high speed USB device using s5p-ehci and address 2
[    2.030338] i2c /dev entries driver
[    2.034359] Linux video capture interface: v2.00
[    2.038637] Initialize JPEG driver
[    2.042006] i2c i2c-1: attached s5p_ddc into i2c adapter successfully
[    2.048198] S5P HPD Driver, (c) 2009 Samsung Electronics
[    2.053760] S5P CEC Driver, (c) 2009 Samsung Electronics
[    2.059235] sysmmu_set_tablebase: CP15 TTBR0 : 0x40004000
[    2.064091] sysmmu_set_tablebase: SYSMMU_G2D sysmmuconp->regs + S5P_PT_BASE_4
[    2.072424] sysmmu_on:SYSMMU_G2D sysmmuconp->regs + S5P_MMU_CTRL:0xE8980000,5
[    2.080532] MFC(Multi Function Codec - FIMV v5.x) registered successfully
[    2.087342] Mali: init_mali_clock mali_clock c05d3c6c
[    2.096307] Mali: Mali device driver 255M loaded
[    2.100402] max17040 1-0036: MAX17040 Fuel-Gauge Ver 02
[    2.101923] Bluetooth: Virtual HCI driver ver 1.3
[    2.106765] Bluetooth: HCI UART driver ver 2.2
[    2.110980] Bluetooth: HCI H4 protocol initialized
[    2.115735] Bluetooth: HCI BCSP protocol initialized
[    2.120681] Bluetooth: HCILL protocol initialized
[    2.125715] cpuidle: using governor ladder
[    2.129894] cpuidle: using governor menu
[    2.133444] mshci: Mobile Storage Host Controller Interface driver
[    2.139550] mshci: Copyright(c) Pierre Ossman
[    2.143984] sdhci: Secure Digital Host Controller Interface driver
[    2.150048] sdhci: Copyright(c) Pierre Ossman
[    2.154424] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (88888888 Hz)
[    2.161172] mmc0: no vmmc regulator found
[    2.166288] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
[    2.172184] s3c-sdhci s3c-sdhci.0: cannot request irq for card detect
[    2.172300] hub 1-1:1.0: USB hub found
[    2.182330] hub 1-1:1.0: 3 ports detected
[    2.182360] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (88888888 Hz)
[    2.182396] mmc1: no vmmc regulator found
[    2.198147] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
[    2.204142] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (88888888 Hz)
[    2.210911] mmc2: no vmmc regulator found
[    2.216001] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA
[    2.222392] usbcore: registered new interface driver usbhid
[    2.227464] usbhid: USB HID core driver
[    2.231687] logger: created 64K log 'log_main'
[    2.235862] logger: created 256K log 'log_events'
[    2.240554] logger: created 64K log 'log_radio'
[    2.245058] logger: created 64K log 'log_system'
[    2.252986] s3c_idma_preallocate_buffer:  VA-e99e0000  PA-2030000  65536bytes
[    2.257062] asoc: max98089 <-> s3c64xx-i2s-v4 mapping ok
[    2.261966] s3c_idma_preallocate_buffer:  VA-e9a00000  PA-2030000  65536bytes
[    2.269482] asoc: max98089 <-> s3c64xx-i2s-v4 mapping ok
[    2.274743] max98089 0-0010: revision ?
[    2.281234] HKDK JACK: Registering jack driver
[    2.282846] ALSA device list:
[    2.285500]   #0: HKDK (MAX98089)
[    2.288908] TCP cubic registered
[    2.292060] NET: Registered protocol family 10
[    2.296831] IPv6 over IPv4 tunneling driver
[    2.301062] NET: Registered protocol family 17
[    2.305141] Bluetooth: L2CAP ver 2.14
[    2.308700] Bluetooth: L2CAP socket layer initialized
[    2.313735] Bluetooth: SCO (Voice Link) ver 0.6
[    2.318246] Bluetooth: SCO socket layer initialized
[    2.323169] Bluetooth: RFCOMM TTY layer initialized
[    2.327985] Bluetooth: RFCOMM socket layer initialized
[    2.333103] Bluetooth: RFCOMM ver 1.11
[    2.336821] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    2.342116] Bluetooth: BNEP filters: protocol multicast
[    2.347325] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.353463] NET: Registered protocol family 33
[    2.358001] RxRPC: Registered security type 2 'rxkad'
[    2.362692] lib80211: common routines for IEEE802.11 drivers
[    2.368493] s5pv310_busfreq_device_init: 0
[    2.372430] ++ s5pv310_cpufreq_init
[    2.375927] -- s5pv310_cpufreq_init
[    2.379666] s5pv310_pm_hotplug_device_init: 0
[    2.383703] SMDKV310 PM-hotplug init function
[    2.388087] VFP support v0.3: implementor 41 architecture 3 part 30 variant 2
[    2.396710] mmc1: new high speed SDHC card at address b368
[    2.401719] mmcblk0: mmc1:b368 H0824 7.45 GiB
[    2.405563] s3c-rtc s3c64xx-rtc: setting system clock to 2011-03-24 02:14:35)
[    2.414132] ctrl->mem.size = 0xf00000
[    2.417712] ctrl->mem.base = 0x54800000
[    2.421855]  mmcblk0:
[    2.423824] FIMC0 registered successfully
[    2.427968]  p1 p2 p3 p4
[    2.432602] ctrl->mem.size = 0xf00000
[    2.433928] ctrl->mem.base = 0x55700000
[    2.438575] FIMC1 registered successfully
[    2.441897] ctrl->mem.size = 0x1800000
[    2.445537] ctrl->mem.base = 0x56600000
[    2.449794] FIMC2 registered successfully
[    2.453440] ctrl->mem.size = 0x600000
[    2.457008] ctrl->mem.base = 0x57e00000
[    2.461077] FIMC3 registered successfully
[    2.465092] S5P TVOUT Driver v3.0 (c) 2010 Samsung Electronics
[    2.521119] usb 1-1.3: new high speed USB device using s5p-ehci and address 3
[    2.594027] init: /init.rc: 200: invalid option 'write'
[    2.594132] init: /init.rc: 200: invalid option 'write'
[    2.598935] init: /init.rc: 200: invalid option 'write'
[    2.604076] init: /init.rc: 203: invalid option 'write'
[    2.609266] init: /init.rc: 203: invalid option 'write'
[    2.614474] init: /init.rc: 203: invalid option 'write'
[    2.619686] init: /init.rc: 203: invalid option 'symlink'
[    2.625095] init: /init.rc: 203: invalid option 'symlink'
[    2.630448] init: /init.rc: 203: invalid option 'chown'
[    2.635656] init: /init.rc: 203: invalid option 'chmod'
[    2.640868] init: /init.rc: 203: invalid option 'chown'
[    2.646072] init: /init.rc: 203: invalid option 'chmod'
[    2.651287] init: /init.rc: 206: invalid option 'setprop'
[    2.656662] init: /init.rc: 208: invalid option 'setprop'
[    2.662041] init: /init.rc: 218: invalid option 'setprop'
[    2.667428] init: /init.rc: 223: invalid option 'setprop'
[    2.669753] generic-usb: probe of 0003:0BDB:1910.0001 failed with error -71
[    2.670362] usb 1-1.3: USB disconnect, address 3
[    2.684363] init: /init.rc: 225: invalid option 'setprop'
[    2.705488] MFC F/W loaded successfully (size: 353404)
[    2.925221] init: cannot open '/initlogo.rle'
[    3.687787] usb 1-1.3: new high speed USB device using s5p-ehci and address 4
[    3.834970] cdc_acm 1-1.3:1.1: ttyACM0: USB ACM device
[    3.848675] cdc_acm 1-1.3:1.3: ttyACM1: USB ACM device
[    3.858363] cdc_wdm 1-1.3:1.5: cdc-wdm0: USB WDM device
[    3.877754] usb 1-1.3: MAC-Address: 0x02:0x80:0x37:0xec:0x02:0x00
[    3.880373] cdc_ncm 1-1.3:1.6: usb1: register 'cdc_ncm' at usb-s5pv210-1.3, 0
[    3.892164] cdc_wdm 1-1.3:1.8: cdc-wdm1: USB WDM device
[    3.899145] cdc_acm 1-1.3:1.9: ttyACM2: USB ACM device
[    4.060424] EXT4-fs (mmcblk0p2): recovery complete
[    4.062690] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. )
[    4.542481] cpu1 turning off!
[    4.598800] IRQ112 no longer affine to CPU1
[    4.599159] CPU1: shutdown
[    4.601863] cpu1 off end!
[    5.301439] EXT4-fs (mmcblk0p3): recovery complete
[    5.303563] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. )
[    6.414251] EXT4-fs (mmcblk0p4): recovery complete
[    6.416146] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. )
[    6.444065] init: cannot find '/system/etc/install-recovery.sh', disabling ''
[    6.455885] enabling adb
[    6.458852] adb_open
sh: can't access tty; job control turned off
# <Android Shell>

[    6.793954] warning: `rild' uses 32-bit capabilities (legacy support in us)
[    7.595705]  max98089_get_playback_path [829] current playback path 0
[    7.596644]  max98089_get_record_path [871] current record path 0
[    7.606730]  max98089_get_playback_path [829] current playback path 0
[    7.609435] cpu1 turning on!
[    7.611914] > max98089_get_record_path [871] current record path 0
[    7.620731] made stopper
[    7.632686] IIS Audio: 16Bits Stereo 44100Hz
[    7.635129] CPU1: Booted secondary processor
[    7.646135] DmaAddr=@2030000 Total=2816bytes PrdSz=704 #Prds=4 dmaEnd=0x20300
[    7.653722]  max98089_get_playback_path [829] current playback path 0
[    7.661505]  max98089_set_playback_path [802] param 2
[    7.670637]  [MAX98089] max98089_set_playback_speaker(94)
[    7.697641] cpu1 on end!
[    7.805839]  [MAX98089] max98089_set_playback_speaker(94)
[    8.697434] cpu1 turning off!
[    8.777702] IRQ112 no longer affine to CPU1
[    8.778086] CPU1: shutdown
[    8.783046] cpu1 off end!
[    9.782337] cpu1 turning on!
[    9.782401] >made stopper
[    9.794396] CPU1: Booted secondary processor
[    9.852895] cpu1 on end!
[   10.857319] cpu1 turning off!
[   10.877438] IRQ112 no longer affine to CPU1
[   10.877628] CPU1: shutdown
[   10.879022] cpu1 off end!
[   11.882417] cpu1 turning on!
[   11.882507] >made stopper
[   11.956294] CPU1: Booted secondary processor
[   12.018185] cpu1 on end!
[   12.857446] s3c-fimc3: FIMC3 1 opened.
[   13.017322] cpu1 turning off!
[   13.077393] IRQ112 no longer affine to CPU1
[   13.077516] CPU1: shutdown
[   13.078608] cpu1 off end!
[   15.083175] cpu1 turning on!
[   15.083295] >made stopper
[   15.115062] CPU1: Booted secondary processor
[   15.182553] cpu1 on end!
[   16.187300] cpu1 turning off!
[   16.208626] IRQ112 no longer affine to CPU1
[   16.208737] CPU1: shutdown
[   16.209536] cpu1 off end!
[   18.212314] cpu1 turning on!
[   18.212373] >made stopper
[   18.351139] CPU1: Booted secondary processor
[   18.408385] cpu1 on end!
[   19.407430] cpu1 turning off!
[   19.467559] IRQ112 no longer affine to CPU1
[   19.467836] CPU1: shutdown
[   19.471116] cpu1 off end!
[   21.809524] request_suspend_state: wakeup (3->0) at 21362253878 (2011-03-24 )
[   22.113749] binder: release proc 2275, transaction 625, not freed