안녕하세요.

고도리입니다.

6명이서 몇달을 헤맨 결과가 나왔습니다........ㅎㅎㅎ
일단 공제보드 조만간 거의 다 살릴 듯 하네요........666Mhz로 잘 돕니다....

로그 올립니다.

U-Boot 1.1.6 (Feb 12 2009 - 15:12:25) for SMDK6410

CPU:     S3C6410@666MHz
         Fclk = 666MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (ASYNC Mode)
Board:   SMDK6410
DRAM:    128 MB
Flash:   0 kB
NAND:    256 MB
*** Warning - bad CRC or NAND, using default environment

In:      serial
Out:     serial
Err:     serial
Hit any key to stop autoboot:  0
smc911x: initializing
smc911x: detected LAN9215 controller
smc911x: phy initialized
smc911x: MAC 00:40:5c:26:0a:5b
TFTP from server 192.168.0.199; our IP address is 192.168.0.100
Filename 'zImage'.
Load address: 0xc0008000
Loading: T #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ####################
done
Bytes transferred = 1765460 (1af054 hex)
Boot with zImage

Starting kernel ...

Uncompressing Linux.................................................................................................................. done, booting the kernel.
Linux version 2.6.21.5-cfs-v19 (root@build) (gcc version 4.2.4) #135 Thu Feb 12 20:31:12 KST 2009
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv6TEJ), cr=00c5387f
Machine: SMDK6410
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
======== s3c6400_map_io: s
======== s3c6400_init_clocks: s
S3C6400: core 666.000 MHz, memory 133.000 MHz, peripheral 66.500 MHz
S3C6400: EPLL 192.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
======== s3c6400_init_uarts: s
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 28956
Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.199:/opt/s3c6400/rootfs6400 ip=192.168.0.100:192.168.0.199:192.168.0.1:255.255.255.0::eth0:off console=ttySAC0,115200n81
======== s3c_init_irq: s
Trying to install chained interrupt handler for IRQ0
Trying to install chained interrupt handler for IRQ1
Trying to install chained interrupt handler for IRQ32
Trying to install chained interrupt handler for IRQ33
PID hash table entries: 512 (order: 9, 2048 bytes)
timer tcon=00600000, tcnt 103c3, tcfg 00000400,00000000, usec 00001340
Console: colour dummy device 80x30
.........s3c_serial_setsource_hw clk->name = mpll_clk_uart
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 114MB = 114MB total
Memory: 111872KB available (3076K code, 431K data, 196K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
======== s3c6400_core_init: s
NET: Registered protocol family 16
======== smdk6410_machine_init: s
======== smdk_machine_init: s
======== s3c6400_irq_init: s
======== s3c6400_dma_init: s
======== s3c6400_init: s
s3c6410: Initialising architecture
======== s3c24xx_dma_init: s
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
======== mem_rw_proc: s
NetWinder Floating Point Emulator V0.97 (double precision)
yaffs Feb 12 2009 17:13:16 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
==========================> s3c_fb_hw_init() ==> GPF14 ==> OUT
=====================1111111ghc.......lte480wv: mach_info = c036e3c8
LCD TYPE :: S3C_LTE480WV LCD will be initialized
PWM channel 0 set g_tcnt = 1000, g_tcmp = 400
gpfcon = 0x20000000
S3C_LCD clock got enabled :: 133.000 Mhz
Window[0]- FB1 : map_video_memory: clear ff600000:000bb800
           FB1 : map_video_memory: dma=57000000 cpu=ff600000 size=000bb800
=====================ghc.......lte480wv: mach_info = c036e3c8
Console: switching to colour frame buffer device 100x30
fb-1069965508:  frame buffer device
lp: driver loaded but no devices found
S3C ADC driver, (c) 2007 Samsung Electronics
S3C ADC driver successfully probed !
ppdev: user-space parallel port driver
s3c-uart.0: s3c_serial0 at MMIO 0x7f005000 (irq = 37) is a S3C
s3c-uart.1: s3c_serial1 at MMIO 0x7f005400 (irq = 38) is a S3C
s3c-uart.2: s3c_serial2 at MMIO 0x7f005800 (irq = 39) is a S3C
s3c-uart.3: s3c_serial3 at MMIO 0x7f005c00 (irq = 40) is a S3C
RAMDISK driver initialized: 8 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
eth0: LAN9215 (rev 0) at 0xc780c000 IRQ 67
eth0: Ethernet addr: 00:09:c0:ff:ec:48
Linux video capture interface: v2.00
Request irq 3 for codec
Request irq 4 for preview
S3C FIMC v3.0
S3C NAND Driver, (c) 2007 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Creating 4 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x00000000-0x00040000 : "Bootloader"
0x00040000-0x00200000 : "Kernel"
0x00200000-0x03200000 : "Root - Cramfs"
0x03200000-0x10000000 : "File System"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 47, io mem 0x74300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-1: new full speed USB device using s3c2410-ohci and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
S3C Touchscreen driver, (c) 2007 Samsung Electronics
kobject_add failed for s3c2410-adc with -EEXIST, don't try to register things with the same name in the same directory.
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
res->start : 7e005000 res->end : 7e0050ff<6>s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
S3C PWM Driver, (c) 2006-2007 Samsung Electronics
i2c /dev entries driver
s3c2410-i2c s3c2410-i2c: slave address 0x10
pdata c0379918, freq 200000 0..200000
clockin 66500
...............freq = 129, iicon = 0x000000e0
s3c2410-i2c s3c2410-i2c: bus frequency set to 129 KHz
Parent clock for Camera = 266000000, CAMDIV = 14
s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
s3c-hsmmc: card inserted.
[s3c_hsmmc_probe]: s3c-hsmmc.0: at 0xc7812000 with irq 56. clk src: sclk_DOUTmpll_mmc0
[s3c_hsmmc_probe]: s3c-hsmmc.1: at 0xc7814000 with irq 57. clk src: sclk_DOUTmpll_mmc1
[s3c_hsmmc_probe]: s3c-hsmmc.2: at 0xc7816000 with irq 49. clk src: sclk_DOUTmpll_mmc2
Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC).
ASoC version 0.13.2
WM9713/WM9714 SoC Audio Codec 0.12
asoc: AC97 HiFi <-> s3c6400-ac97 mapping ok
ALSA device list:
  #0: SMDK6400 (WM9713)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time
eth0: link down
eth0: TX data FIFO space available irq
IP-Config: Complete:
      device=eth0, addr=192.168.0.100, mask=255.255.255.0, gw=192.168.0.1,
     host=192.168.0.100, domain=, nis-domain=(none),
     bootserver=192.168.0.199, rootserver=192.168.0.199, rootpath=
Looking up port of RPC 100003/2 on 192.168.0.199
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Looking up port of RPC 100005/1 on 192.168.0.199
VFS: Mounted root (nfs filesystem).
Freeing init memory: 196K
INIT: Entering runlevel: 3
sh: 0: unknown operand

Welcome to the AESOP S3C2440A world !!!(0.1)

You may now login as 'root'.

godori login: root
 
Linux 2.6.21-MEP2440
 
 /) /)
(='.'=)
 
login[2113]: root login on 'tts/0'
S3C6400 MFC Driver, (c) 2007 Samsung Electronics
[MFC_DRV: TRACE] MFC_HW_Init: Download  FirmwareIntoBitProcessor  OK.
[MFC_DRV: TRACE] GetFirmwareVersion : GET_FW_VER command was issued.
[MFC_DRV: TRACE] GetFirmwareVersion: GET_FW_VER => 0xF202, 0x1306
[MFC_DRV: TRACE] BUSY_FLAG: BUSY_FLAG => 0
S3C6400 MFC driver module init OK.
S3C PostProcessor Driver, (c) 2007 Samsung Electronics
root@godori:~# ./gmp m.mp3
¸®µå ³¡³µ´Ù.

========================BUF_START========================
char buf[0]=[255]
char buf[1]=[250]
char buf[2]=[144]
char buf[3]=[68]
char buf=[ff][fa][90][44]
bit=11111111111110101001000001000100
========================BUF_END========================

                mp3 Çì´õ ½ÃÀÌÀÚ¾Ç~~~~!!]!!

[µ¿±âÆÐÅÏOK!!]!!

MPEG Audio Version ID = [3]  MPEG Version 1(mp3ÀÇ °æ¿ì)

Layer Á¤ÀÇ            = [1]  Layer III

»ùÇøµ ÁÖÆļö         = [44100] j = 2

Channel Mode          = [2]  Joint Stereo

È®Àå Mode             = (Joint Stereo¿¡¼­¸¸ »ç¿ë)¿©¼­ ÇöÀç °Ç³Ê¶Ú´Ù.

Checksum ¼³Á¤À¯¹«     = [0]  Error üũ ÀÖÀ½ 

Padding bit           = [0]  frame is not padded 

°³º°¿ëµµºñÆ®          = Ưº°È÷ »ç¿ëµÇÁö ¾ÊÀ½ 

Copyright             = [0]  Audio is not copyrighted  

Original              = [1]  ¿øº»   
mp3_struct.bit_rate=[9] BitRate             = 128 Kbit
continue
mp3_struct.loop[2] = 44100

od->aout_frags  = 32
od->aout_fragsize = 4096
od->aout_tsize    = 131072
od->aout_bytesps  = 176400
od->aout_freq     = 44100
od->aout_channels = 2
od->aout_format   = 16

os->frags         = 32
os->fragsize      = 4096
os->freq          = 44100
os->channels      = 2
os->format        = 16
file position = 0
Audio decoding

root@godori:~#

사운드까지 테스트한 로그입니다.

슬슬 공제 시작합니다...^^