안녕하세요?

이솝 S5PC100 공동제작 보드가 배송되길 기다리시는 분들께 관련 진행 사항 안내 드립니다.

현재 이솝 S5PC100 보드의 샘플 양산 PCB 조립 및 테스트가 완료 되었으며, 동작 화면은 다음과 같습니다.

공동제작 보드의 배송 일정은 보드 테스트를 진행하면, 다음 주 정도에 배송이 가능할 것으로 예상 됩니다.

LCD의 경우 다른 곳에서 어떻게 수급을 하여, 5월 1주에 일괄 배송이 가능할 듯 싶습니다. :)

그 동안 기다려주신 분들께 감사의 말씀 드립니다. :)

# 안드로이드 동작 화면

# 보드 후면 동작 사진

# X-Windows 동작 사진

 

# 부팅로그

U-Boot 1.3.4 (Apr 28 2010 - 14:04:19) for NT-S5PC100 (Rev.01)


CPU:     S5PC100@666MHz
         Fclk = 1332MHz, Hclk = 166MHz, Pclk = 66MHz, Serial = PCLK
Board:   NT-S5PC100 Serise
DRAM:    256 MB
Flash:   0 kB
SD/MMC:  Card not found
NAND:    512 MB
In:      serial
Out:     serial
Err:     serial
Hit any key to stop autoboot:  0
smc911x: initializing
smc911x: detected LAN9215 controller
smc911x: phy initialized
smc911x: MAC 00:40:5c:26:0a:5b
TFTP from server 192.168.1.15; our IP address is 192.168.1.85
Filename 'zImage-S5PC100'.
Load address: 0xc0008000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #####################################
done
Bytes transferred = 2186036 (0x215b34)
Boot with zImage

Starting kernel ...

Uncompressing Linux...................................................................................................................................
Linux version 2.6.29 (jhkim@jhkim-uBuntu) (gcc version 4.3.1 (GCC) ) #64 Tue Apr 27 11:13:50 KST 2010
CPU: ARMv7 Processor [412fc081] revision 1 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDKC100
Ignoring unrecognised tag 0x41001099
Memory policy: ECC disabled, Data cache writeback
CPU S5PC100 (id 0x43100000)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S5PC100: PLL settings, A=1332000000, M=267000000, E=67500000, H=24000000
S5PC100: ARMCLK=666000000, HCLKD0=166500000, PCLKD0=83250000, HCLK=133500000, PCLK=66750000
mout_apll: source is fout_apll (1), rate is 1332000000
mout_epll: source is fout_epll (1), rate is 67500000
mout_mpll: source is mpll (1), rate is 267000000
mout_hpll: source is srclk (1), rate is 24000000
mmc_bus: source is dout_mpll (1), rate is 44500000
mmc_bus: source is dout_mpll (1), rate is 66750000
mmc_bus: source is dout_mpll (1), rate is 66750000
usb-host-bus: source is dout_mpll (1), rate is 133500000
uclk1: source is dout_mpll (1), rate is 66750000
sclk_spi: source is dout_mpll2 (1), rate is 66750000
sclk_spi: source is dout_mpll2 (1), rate is 66750000
sclk_spi: source is dout_mpll2 (1), rate is 66750000
sclk_audio: source is mout_epll (0), rate is 67500000
audio-bus: source is mout_epll (0), rate is 67500000
audio-bus: source is mout_epll (0), rate is 67500000
audio-bus: source is fout_epll (0), rate is 67500000
sclk_irda: source is dout_mpll (1), rate is 133500000
sclk_pwi: source is srclk (0), rate is 0
sclk_fimd: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_fimc: source is dout_mpll (1), rate is 133500000
sclk_mixer: source is clk_27m (0), rate is 27000000
s5pc1xx: 6291456 bytes system memory reserved for fimc0 at 0x2070f000
s5pc1xx: 6291456 bytes system memory reserved for fimc1 at 0x20d0f000
s5pc1xx: 6291456 bytes system memory reserved for fimc2 at 0x2130f000
s5pc1xx: 33554432 bytes system memory reserved for mfc at 0x2190f000
s5pc1xx: 33554432 bytes system memory reserved for jpeg at 0x2390f000
s5pc1xx: 8388608 bytes system memory reserved for pmem at 0x2590f000
s5pc1xx: 3145728 bytes system memory reserved for pmem_gpu1 at 0x2610f000
s5pc1xx: 6291456 bytes system memory reserved for pmem_adsp at 0x2640f000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: mem=256M root=/dev/nfs rw nfsroot=192.168.1.15:/nfsroot/RootFS-S5PC100 ip=192.168.1.20:192.168.1.15:192.168.1.1:255.255.255:0::e1
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
console [ttySAC1] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 153088KB available (4064K code, 848K data, 180K init)
Calibrating delay loop... 665.19 BogoMIPS (lpj=1662976)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 564 bytes
S5PC1XX GPIO Driver Init
NET: Registered protocol family 16
S5PC100: Initialising architecture
S3C PL330-DMA Controller Driver, (c) 2008-2009 Samsung Electronics
Total 24 DMA channels will be initialized.
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
S5PC100 Button init function
 11 Button Interrupt occure
No such irq number 47<4>NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
yaffs Apr 26 2010 19:58:11 Installing.
msgmni has been set to 299
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
s3cfb s3cfb: [fb0] dma: 0x2fa00000, cpu: 0xff000000, size: 0x00177000
Console: switching to colour frame buffer device 100x30
s3cfb s3cfb: registered successfully
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
s5pc100-uart.0: s3c2410_serial0 at MMIO 0xec000000 (irq = 16) is a S3C6400/10
s5pc100-uart.1: s3c2410_serial1 at MMIO 0xec000400 (irq = 20) is a S3C6400/10
s5pc100-uart.2: s3c2410_serial2 at MMIO 0xec000800 (irq = 24) is a S3C6400/10
s5pc100-uart.3: s3c2410_serial3 at MMIO 0xec000c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
pmem: 1 init
pmem_gpu1: 1 init
pmem_adsp: 1 init
PPP generic driver version 2.4.2
eth0 (smc911x): not using net_device_ops yet
eth0: LAN9215 (rev 0) at 0x98000000 IRQ 38
eth0: Ethernet addr: 00:09:c0:ff:ec:48
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
Linux video capture interface: v2.00
S5PC100 MFC Driver, (c) 2009 Samsung Electronics
S3C Rotator Driver, (c) 2008 Samsung Electronics
s3c_rotator_probe called
s3c_rotator_probe success
S3C G3D Driver, (c) 2007-2009 Samsung Electronics
s3c_g3d version : 0x1020100
G3D_RESERVED_MEM_SIZE : 32 MB
G3D_CHUNK_SIZE : 2 MB
G3D_CHUNK_NUM : 16
g3d is registered successfully!<4>Driver 'sd' needs updating - please use bus_type methods
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using software ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 512MiB 3,3V 8-bit":
0x000000000000-0x000000080000 : "Bootloader"
0x000000080000-0x000000400000 : "Kernel"
0x000000400000-0x000020000000 : "File System"
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 87, io mem 0xed400000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android init
android_bind
mass_storage_function_add
android_usb gadget: Number of LUNs=1
adb_function_add
android_usb gadget: android_usb ready
Registered gadget driver 'android_usb'
mice: could not register psaux device, error: -16
mice: PS/2 mouse device common for all mice
input: nt-keypad as /devices/virtual/input/input0
Aesop Keypad Initialized!!
S3C Touchscreen driver, (c) 2008 Samsung Electronics
S3C TouchScreen got loaded successfully : 12 bits
PRESS KEY : KEY_RIGHT
Press keycode = 106
input: S3C TouchScreen as /devices/virtual/input/input1
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2410-i2c s3c2410-i2c.0: slave address 0x10
s3c2410-i2c s3c2410-i2c.0: bus frequency set to 379 KHz
s3c2410-i2c s3c2410-i2c.0: i2c-0: S3C I2C adapter
s3c2410-i2c s3c2410-i2c.1: slave address 0x10
s3c2410-i2c s3c2410-i2c.1: bus frequency set to 379 KHz
s3c2410-i2c s3c2410-i2c.1: i2c-1: S3C I2C adapter
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (44500000 Hz)
Registered led device: mmc0::
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (44500000 Hz)
Registered led device: mmc1::
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133500000 Hz)
s3c-sdhci s3c-sdhci.2: clock source 2: mmc_bus (44500000 Hz)
Registered led device: mmc2::
mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI s5p-spdif
No device for DAI HDMI-SPDIF Codec
asoc: HDMI-SPDIF Codec <-> s5p-spdif mapping ok
ALSA device list:
  #0: smdks5p (HDMI-SPDIF)
TCP cubic registered
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
s3c-fimc: fimc_configure_subdev: v4l2 subdev board registering failed
s3c-fimc: fimc_configure_subdev: v4l2 subdev board registering failed
S5PC1XX TVOUT Driver, (c) 2009 Samsung Electronics
s5p-tvout s5p-tvout: hpd status is cable inserted
s3c2410-rtc s3c2410-rtc: setting system clock to 2009-09-16 12:49:21 UTC (1253105361)
usb 1-1: new full speed USB device using s3c2410-ohci and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
eth0: link down
IP-Config: Complete:
     device=eth0, addr=192.168.1.20, mask=255.255.255.0, gw=192.168.1.1,
     host=0, domain=, nis-domain=(none),
     bootserver=192.168.1.15, rootserver=192.168.1.15, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.15
eth0: link up, 100Mbps, half-duplex, lpa 0xCDE1
Looking up port of RPC 100005/1 on 192.168.1.15
VFS: Mounted root (nfs filesystem) on device 0:13.
Freeing init memory: 180K
INIT: Entering runlevel: 5
Starting Dropbear SSH server: dropbear.
Starting system message bus: dbus.
Starting syslogd/klogd: done
Starting Connection Manager
scsi 0:0:0:0: Direct-Access     LG       X TICK           1100 PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 7831552 512-byte hardware sectors: (4.00 GB/3.73 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 7831552 512-byte hardware sectors: (4.00 GB/3.73 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
Starting GPE display manager: gpe-dm
Executing mount /dev/sda1 to /media/sda1, action=add

  _____ _____ _____ _____ _____
 |  _  |   __|   __|     |  _  |
 |     |   __|__   |  |  |   __|
 |__|__|_____|_____|_____|__|.or.kr
 
 (C)2010 aESOP Embedded Forum.                             
 aESOP S5PC100 Embedded Linux Platform.

 System  : S5PC1xx
 Console : s3c2410_serial1

S5PC1xx login: root
root@S5PC1xx:~# mmc0: new high speed SDHC card at address aaaa
mmcblk0: mmc0:aaaa SU08G 7.40 GiB
 mmcblk0: p1
Executing mount /dev/mmcblk0p1 to /media/mmcblk0p1, action=add
mmc0: card aaaa removed
Executing mount /dev/mmcblk0p1 to /media/mmcblk0p1, action=remove
mmc0: new high speed SDHC card at address aaaa
mmcblk0: mmc0:aaaa SU08G 7.40 GiB
 mmcblk0: p1
Executing mount /dev/mmcblk0p1 to /media/mmcblk0p1, action=add

root@S5PC1xx:~#